Sendust alloy flat metal powder
Without adversely side effects to the sound quality and video, and use the material "sendust alloy" with a strong noise absorption capacity. In sendust alloy (SENDUST) is old and new material, has been developed in Sendai in the 1930s, magnetic loss ability is high, Al, is the alloy of domestically made from Fe, SiO2. It succeeded in processing the expensive and processing is difficult sendust alloy powder of high flat shape of the electromagnetic wave absorption performance.Further, to form an oxide film on the powder surface, secure insulation.
Polyethylene-based special rubber
The sendust alloy as uniform and the base member closely packed, using polyethylene special rubber, mixing the best mixing ratio. In addition, the flat shape powder to polyethylene-based special rubber layer by a special production method, by uniform and oriented parallel to, won the maximum electromagnetic wave absorption performance.
AV equipment, power supply path, personal computer, such as consumer electronics products a wide range of applications
AV transformer around the equipment, chassis, such as the periphery of the input-output terminal, is effective and paste in-prone part of the noise. In addition, the plug portion of the power cable and audio / video signal cable wound to the (easier to emit a noise, and more likely to be exposed to noise), also paste to the side or outlet plate of the wall outlet is recommended. PC chassis and power supply around, modem and noise to release an easy-peripheral devices such as a hard disk, you can still use it in such as electronic musical instruments and recording equipment. In addition, such as noise measures of a general consumer electronics products can be used for multi-purpose.
Audio component, cable, plug, such as an analog item, please try to become a trial in the place where I think each here.Places where use is up to you.
For example, the noise absorption of around power source such as a power plug and outlet. Near the outlet, such as plug and outlet, because the noise is likely to occur is also the effect of the MWA is remarkable. May be pasted over plug the entire circumference, also has the effect partial. Relatively to paste the arc large cover of such power plug, MWA-030 is the best choice.Since the MWA-030 is flexible, you also familiar to some of the irregularities. It should be noted, MWA is a sheet that contains a metal powder, since the cross-section has a conductivity, the electrode portion of electricity flows on the careful not to touch the MWA, please copy and paste. Accidentally paste if there is a short circuit or fire fear of.
MWA also in analog item you can use. Record around for phono signal from the cartridge is extremely weak, is exceptionally sensitive to noise. For example, the head shell back near the lead wire is work wonders. A clear haze sunny sound can be obtained.Besides that, depending on your idea, stuck in various places, please try to become to try the extent of the effect of the MWA.The thickness of the MWA to be used in the analog item Please choose in the right man in the right place. The MWA-100S if the damping effect also aim, the most thin MWA-010T if pasted into sharp bend surface, the flat or gently curved surface would be the better choice MWA-030.
The pasting the MWA to cable such as RCA cable, the most orthodox and easy-to-understand how to use the effect. It is may be affixed to the cover of the plug, you do not have to be wrapped around the middle of the cable. In that case, it is not necessary to cover the entire portion of the cable, please try to wound one to several turn away from the plug of 10-20 centimeters. The most suitable for pasting to, such as a cable or RCA plug is the MWA-010T which is excellent in most thin and flexibility in MWA.
Please try the MWA is also on the top plate and bottom plate of the audio equipment. So as not to block the heat sink, over and identifies an optimal size, please use the MWA was cut into the size. If you put on top of the top plate, you can just put as it is without peeled off the release paper. While placed on the top plate of the equipment, it would be interesting to locate the place where good-handed most. Rotating part such as a motor, power supply unit, such as transformers and switching circuit, where the IC and the CPU is located, that is the most effective paste it into the chassis in the vicinity of the place where the electromagnetic noise is easy to get. However, once pasted MWA with the passage of years will be difficulty peeling progressed solidification of the pressure-sensitive adhesive. There is a possibility that can not be cleanly removed even want peeled off, please go at your own risk if you paste. Paste to the interior of the equipment, Paste MWA is dropped in the heat and aging depending on the position, so could induce failure of the equipment, please be careful in self-responsibility.
Clear to reduce the environmental impact of the RoHS Directive
Environmentally hazardous substances (lead, mercury, hexavalent chromium, cadmium, etc.) with the following measurement limit the content of, you have to clear the RoHS directive.
Excellent noise absorption effect in a simple use
Usage is quite simple. Such as the power supply unit and the input and output terminals of the audio equipment, around the prone point of noise, by pasting in the cable and plug, exhibit a high noise-canceling effect. S / N sense is good, and improve resolution. In addition, bleeding of contour is decreased in the video, effects such as sharpness of the color increases can be obtained. SN is in sound quality, resolution, improvement of response, gradation expression is in the video, and contribute to, such as improvement of color.
Sheet tape, colorful variation of the thickness and size
Assuming a variety of needs and point-of-use, available in addition to the 0.3mm sheet A4, A5, A6 size), with a thickness of 0.1mm tape, such as a thickness of 1.0mm sheet, a variation of the variety of sizes and thicknesses Did. In the case of sheet, as it is placed on the AV top plate without cut, or has the effect just lay under the equipment. In the case of tape, it is useful in wound to the cable and plug.
Cut with scissors and paste, flexible workability
Can be easily cut with scissors or the like, excellent flexibility, cable, etc., it is also sticking possible to a curved surface.Workability, and excellent workability. Polyethylene-based special rubber, sufficient tensile strength and extensibility, have Bei also serves as a flexible work of goodness so, paste is very good. In addition, the pressure-sensitive adhesive surface to achieve adequate adhesion, and maintain long-term Paste performance. In addition, the surface of the sheet-tape is a chic silver, it does not stand out at the time of use. The paste with a slight tension is the clean finish tips.
UL94V-0 safety design that won the flame retardant
UL94V-0 has a flame-retardant (UL File No.188467), it is also considered to safety.
PRECAUTIONS
- Since the metal powder surface is coated with an oxide film, but have insulating properties, the cut surface of the sheet tape is electrically conductive. Please avoid be pasted directly into the conduction part just in case.
- After paste, paste strength in about two to three days at room temperature is the maximum.
- Heat resistance corresponds to -20 ~ 90 ℃ and a wide range of operating temperature, but the paste to the point of overheating and cooling is expected to exceed this temperature (CPU, GPU, such as a vacuum tube) Please avoid.
- Such as closing the amplifier and the personal computer of the heat radiation holes, how to use such that interfere with heat dissipation Please avoid.
- Do not store in a state where it is exposed to direct sunlight.
- Since there is a possibility that the pressure-sensitive adhesive is degraded, as much as possible storage in a high temperature and high humidity condition, please avoid using.
- A long period of time, avoid storage and use in the state plus the excessive load on the product (in thickness of the product is changed, electromagnetic wave absorption characteristics might change).
- Please working crucifixion from wipe well the dust and oil of the adherend (mating surface).
- If you have been kept at a low temperature state, please use the left to stand at room temperature and normal humidity in a few hours. (Low-temperature storage and have the product, the pressure-sensitive adhesive is cured, there is a possibility that the initial adhesive becomes weak. And allowed to stand at room temperature and normal humidity in the pressure-sensitive adhesive becomes soft and sticky to recover.)
- It weakened the adhesive force to repeat the peel-and-paste.
- Pressure-sensitive adhesive is the remaining hard to design, but just in case, do not stuck in a location, such as troubled and Paste trace remains.
- After pasting, you can be peeled off by hand, just in case, the paste to the point you can not afford and can not be peeled off please avoid.
Specification
MWA-010 T: Tape wound (0.1mm × 20mm × 5m)
MWA-030 L: A4 (0.3mm × 210mm × 297mm)
MWA-030 M: A5 (0.3mm × 148mm × 210mm)
MWA-030 S: A6 (0.3mm × 105mm × 148mm)
MWA-100 S: (1.0mm × 105mm × 165mm)
Electromagnetic wave absorption material: Sendust alloy flat metal powder (Al · Fe · SiO2), forming an oxide film on the metal powder surface.
Base material: Polyethylene-based special rubber
Adhesive face: There adhesive surface on one side (use peel off the release paper)
Operating temperature limit: -20 ~ 90 ℃
Volume resistivity: 5 × 106 Ω · cm
Tensile strength: 6.0MPa
Flame retardance: UL94V-0 (UL File No.188467)
